Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Blog Article
Here down the page you can locate a good deal of excellent information and facts relating to How to Install a Bathtub Yourself.
Setting up a bathtub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily easily accessible, the task can move rapidly; if you have to open up a wall surface to remove the old tub as well as place the new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the task and also are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed project, it is better to think about using one prior to you begin. Opportunities are you might require a professional plumber to make tube links.
This post will assist you install a brand-new bath tub in your restroom if you have actually currently bought a brand-new tub and don't need to alter the plan of your previous water supply pipelines.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite problematic as a result of the limited gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the tap in place with the supplier provided backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type needs to be connected to the tap finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Using both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub until the level reads level.
To install taps, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Switch on the water system and also examine all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub as well as likewise inspect the overflow electrical outlet and the normal outlet for leakages.
Ultimately, fix the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has been made use of at least once as this will resolve it right into its last placement.
Planning for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall surface in between the bath and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealer can split rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very intrigued by How to Install a Bathtub Yourself and I hope you liked the piece. So long as you enjoyed our blog post plz be sure to share it. Thank-you for taking the time to read it.
Maintenance Sign-Up
Report this page